KB TZ2 expansion anchor technical supplement December 2020 5 Table 3 Hilti Carbon Steel KB TZ2 design strength based on concrete failure modes in cracked concrete per ACI 318 14 Ch 17 1 2 3 4 5Nominal anchor diameter in Effective embedment in mm Hilti Inc 7250 Dallas Parkway Suite 1000 Plano TX 75024 1 800 879 8000 www hilti com November 1 2021 RE Hilti KB TZ2 to replace Hilti KB TZ To Whom It May Concern For over 10 years Hilti has been providing the Kwik Bolt TZ KB TZ carbon andThe Hilti KWIK HUS EZ and KWIK HUS EZ P screw anchors are alternatives to cast in place anchors described in Section 8 1 3 2016 or 2013 edition or Section 2 1 4 2011 2008 or 2005 edition of TMS 402 ACI 530 ASCE 5 as applicable as referenced inThe Hilti Kwik Bolt TZ anchor KB TZ is used to resist static wind and seismic tension and shear loads in cracked and uncracked normal weight concrete and sand lightweight concrete having a specified compressive strength f′c of 2 500 psi to 8 500 psi 17 22009 4 30 nbsp 0183 32 The Hilti Kwik Bolt TZ or KB TZ is a mechanical type expansion anchor that is torque controlled and is made up of an anchor body wedge clip and a nut amp washer The Kwik Bolt TZ is manufactured in carbon steel that is zinc plated as well as in

HILTI INC EVALUATION SUBJECT KWIK BOLT TZ2 MASONRY ANCHORS 1 0 EVALUATION SCOPE Compliance with the following codes 2018 2015 and 2012 International Building Code 174 IBC 2018 2015 and Is producing Kwik Bolt TZ KB TZ stopped if yes what series is the replacement Remove nut from KB TZ anchor to replace bracket re install nut I have an existing 1 2 quot diameter KB TZ bolt that is anchored to a concrete slab through a steel bracket Hilti Wedge Anchors Kwik Bolt 3 Wedge anchor High performance wedge anchor with everyday approvals for uncracked concrete carbon steel Approved by ICC ES for use in masonry and concrete Rounded end for easy installation Dog point impact The Hilti Kwik Bolt TZ anchor KB TZ is used to resist static wind and seismic tension and shear loads in cracked and uncracked normal weight concrete and lightweight concrete having a specified compressive strength f ′ c of 2 500 psi to 8 500 psi 1758 6see ESR 1917 LABC and LARC Supplement Property evaluated Structural 2 0 USES The Hilti Kwik Bolt TZ anchor KB TZ is used as anchorage to resist static wind and seismic Seismic Design Categories A through F tension and shear loads in

Hilti Kwik Bolt 3 KB3 Hilti KBV TZ Simpson Strong Bolt 2 Power Stud 174 SD2 High Performance Carbon Steel Wedge Anchor ESR 2502 3 8 quot 3 4 quot 2021 11 5 nbsp 0183 32 CA38X334 Hilti 174 Kwik Bolt Carbon Steel TZ 3 8″ x 3 3 4 Installation Instructions Capacity 10 000 lbs 100 Series Lift Anchor Hilti Kwik Bolt III 3 4″ x 5 1 2″ Anchors supplied with the lift Hilti HIT HY 150 Hilti Kwik Bolt III 3 4″ x 5 1 2″ 4 1 4″ 108mm Hilti HY200 Evaluation Service ESR 1917 Hilti KWIK Bolt TZ Carbon and Stainless Steel Anchors in Concrete The relevant design parameters are reiterated in Tables 1 2 and 3 of this document Supplemental provisions required for the design of the KB TZ are enumerated in Section 4 0 of ESR 3785 Kwik Bolt TZ Expansion Anchors in Masonry June 2016 ESR 3814 HIT RE 500 V3 Adhesive Anchors and Post Installed Reinforcing Bar Connections 2015 June 2016 ESR 3829 HIT RE 100 Adhesive Anchor 2015 June 2016 HILTI ICC ES REPORTS From 624 00 Kwik Bolt 1 carbon steel wedge anchor premium High performance wedge anchor for cracked concrete and seismic carbon steel From 45 75 Kwik Bolt TZ Wedge anchor ultimate Ultimate performance wedge anchor with approvals for cracked concrete and seismic carbon steel From 248 00

Tags: